driven roller造句
例句與造句
- Nonlinear mechanical analysis of belt on driving roller
驅動部輸送帶的非線性力學分析 - 2 roller : driving roller , direction - chage roller and surface - add roller
2滾簡：分傳動滾簡改向滾簡和增面滾筒。 - Diameter of punched driving roller is large , suiting rewinding of large and small roll
復卷驅動輥直徑大，適應大小卷徑的復卷。 - The drive motor that turns the rubberised drive roller is a high performance stepping motor
轉動膠制走紙滾筒的驅動電機是高性能的步進電機。 - The platform is divided into three driving segments , adopting three speed - stepless motors to drive roller via wheel gear
調速輸坯臺分3段傳動，采用3臺無級變速電機通過齒輪帶動輥棒。 - It's difficult to find driven roller in a sentence. 用driven roller造句挺難的
- This shall erect bell cleanup scrapper in front of belt - drive roller , so that this clean up crude coal adhered onto belt
皮帶驅動輥筒前安裝有皮帶清潔刮板，清除粘結于皮帶上的原煤。 - S97 permanent magnet pulley can be selected as driving roller of this machine so that magnetic separation treatment can be carried out at the same time
該機的傳動滾簡可以選用s97系列永磁皮帶輪，以便同時進行磁選處理。 - 5 sweeper : caput sweeper is installed at lower part of driving roller , while vacant section sweeper is installed at the end , near the direction - chage roller
5清掃器：頭部清掃器安裝在傳動滾筒下方，空段清掃器安在尾部改向滾筒附近 - One end of belt - driven roller is fixed with machine body . the other end links with bolt - mode coupler at axial end of reducer . so that belt is easier replaced
皮帶驅動輥筒一端固定于機體上，一端與減速機軸端插銷式聯軸器相連，使皮帶更換更容易。 - Feeding and face fixing part : vfc motor , reduction drive , initiative , passivity drive roller . belt roller , face fixing , trimming and special width tape
輸送整形部分：由變頻控制電機、減速機、主、被動傳動輥、調帶輥、整形、修邊及特種寬面膠帶組成。 - When the swing arm axis made in the installation and wavering on the previous drive rollers above , this machinery can be directed to move forward for the movement and transport equipment
當搖擺臂安裝在出力軸上和在搖擺傳動器前面的滾子上面時，此機械可被引導一直向前運動并用作運輸備。 - The driving rollers are electroplated with hard cr , tension self - controlling of winding - rollers are applied to the driving unit . the barrel of extruder , bullhead tee and die adopt cast aluminum heater which is endurable
擠出機料筒三通和模頭均采用鑄鋁加熱，牽引輥筒電鍍硬鉻，輪鏈輪采用 - 1 driving part : this machine adopts triangle beltdouble - grade drive for shaft speed reducer , speed reducer is installed on shaft head of driving roller ; all driving devices are installed on the machine frame viahead sheave rack and motor rack
1驅動部分：該機采用三角皮帶軸裝式減速器兩級傳動，減速器套裝在傳動滾筒的軸頭上全部傳動裝置通過頭輪架和電機架懸掛安裝在機架上。 - The driving rollers ’ design is always the problem for belt conveyor factory and its design has been researched home and abroad for a long time . but the traditional design methods have many disadvantages . in the paper the driving rollers and the other key parts are analyzed with finite element parametric analysis method which is recently applied broadly
傳動滾筒的設計一直是輸送機生產廠家的一個難點,本文在分析了國內外研究和應用現狀的基礎上,總結了傳統設計方法的不足,并應用目前廣為使用的有限元方法對傳動滾筒及其它關鍵部件進行了參數化分析。 - Supporting roller 12 : it can be dismantled to be repaired if the surface of roller is abraded , or channel of rollers is abraded unequally , or there is sunken hole , make sure that the two roller channels should have same diameter and be coaxial , outer diameter of the pair supporting rollers of every driving roller should be similar
輥面磨損或輥道不均勻磨損或產生凹坑時可拆下精車修理，但注意輥體的二個輥道直徑一致并同軸，每個傳動輥的一對托輥外徑保持一致。